Users Manual Snap 700 Linear Knife Addendum AVERY DENNISON Manual Edition 2.2 7 February 2014 Manual Part Number 621395
10 Maintenance Snap Linear Knife Maintenance Cleaning Feed / Nip Rollers The Linear Knife has a set of feed rollers that keep web tension betwee
Snap Linear Knife Maintenance 11 Knife Blade Replacement Replace the wheel blade when it becomes dull or nicked. The knife has a life expectancy
12 Maintenance Snap Linear Knife 3. Remove the six 8-32 Button Head Screws and remove the left and right side covers. 4. Remove the entry
Snap Linear Knife Maintenance 13 6. Removing the upper stationary blade allows access to the wheel blade. Remove the wheel blade, bearing, an
14 Maintenance Snap Linear Knife 9. Re-install the covers and knobs.
Snap Linear Knife Maintenance 15 Knife Blade Cleaning When the material starts to have poor cut along all or part of the cut edge, the knife blad
16 Maintenance Snap Linear Knife 3. Remove the six 8-32 Button Head Screws and remove the left and right side covers. 4. Remove the entry
Snap Linear Knife Maintenance 17 7. Re-install the upper stationary blade with the four Phillips flat head screws removed from step 5. Be sure
18 Adjustments Snap Linear Knife Adjustments Web Tracking in Center of Printer NOTE: Cut quality and straightness requires the stock to track d
Snap Linear Knife Adjustments 19 8. Run the printer again and see if there is a walking issue, if so repeat steps 4-6. 9. If the stock wants to
ii Snap Linear Knife WARNING This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condition
20 Adjustments Snap Linear Knife Knife Cam Adjustment The cam adjustment keeps the frame from distorting during operation and affects the cut an
Snap Linear Knife Adjustments 21 Web Tracking Adjustment If the web is tracking through the SNAP 700 printer but is not tracking into the Knife
22 Adjustments Snap Linear Knife 1. Loosen the ¼-20 cap screw shown. Rotating the thumb wheel will rotate the knife in one direction or the oth
Snap Linear Knife Adjustments 23 Adjusting the Sensor The SNAP 700 Linear Knife has the capability to sense through hole, slot, top reflective, o
24 Adjustments Snap Linear Knife 4. Remove the Phillips head screw securing the idler gear standoff shown and remove the standoff with gear so
Snap Linear Knife Adjustments 25 7. Re-install the idler gear removed from Step 4. 8. Re-install the left side cover and secure with the thre
26 Adjustments Snap Linear Knife Positioning the Sensor To position the sensor correctly for a thru-hole format, the web must be tracking throug
Snap Linear Knife Adjustments 27 sensors” and begin to run. If the sensor is not in the correct position, the printer will stop. Traverse the s
28 Adjustments Snap Linear Knife 3. Start the printer back up, as the stock passes through the knife, the supply light on the 700 should light
Snap Linear Knife Adjustments 29 Centering the Knife to the Web After the web is tracking through the printer and into the knife straight, it may
Snap Linear Knife iii Contents Scope 5 Introduction ...
30 Adjustments Snap Linear Knife 4. Loosen the thumb screw holding the upper and lower halves of the Linear Knife together. Loosen the lower
Snap Linear Knife Adjustments 31 7. Tighten the E-S Nut and the thumbscrew. 8. Feed the web through the knife and run some sample labels to
32 Adjustments Snap Linear Knife 10. Once the web is centered, remove the web from the Linear Knife and remove the feed knob. 11. Insta
Snap Linear Knife Trouble Shooting 33 Trouble Shooting Problem Probable Cause Corrective Action Cut is out of square 1. Web not centered in pr
34 Snap Linear Knife 1. Damaged sensor 1. Replace sensor harness assembly. Reflective sensor error 1. Sensor not aligned with mark 1. Mo
Snap Linear Knife Appendix A 35 Appendix A The SNAP 700 Printer will need minor alterations to have a Linear Knife installed. These alterations
36 Appendix A Snap Linear Knife Removing the Nip Assembly The Linear Knife will use the existing nip assembly and mount hardware from the printe
Snap Linear Knife Appendix A 37 Removing the Knife Assembly The Linear Knife has its own feed and will reuse the existing printer nip assemblies.
38 Appendix A Snap Linear Knife 3. Remove the feed / knife tie bracket. There are two 10-32 x1/4” Button head screws to removed using a 1/8” he
Snap Linear Knife Appendix A 39 Removing the Rear Cover 1. Turn off the power to the printer at the end of a batch so not to lose downloaded d
iv Snap Linear Knife Replace the Motherboard Entry ... 40 Install
40 Appendix A Snap Linear Knife Installing the Linear Knife - Electrical Updates Replace the Motherboard Entry On field upgrades to the SNAP 70
Snap Linear Knife Appendix A 41 4. Remove the six screws holding down the motherboard. 5. Slide the motherboard back and out of the way t
42 Snap Linear Knife 7. Remove the last two screws holding the motherboard entry bracket to the base frame. Remove motherboard entry bracket.
Snap Linear Knife 43 11. Slide the MCB upright back into the slot on the motherboard. 12. Install the screws mounting the upright bracket t
44 Snap Linear Knife Install Internal Harnesses 1. Remove the two connector plates covering the large slot and hole as shown. 2. Find
Snap Linear Knife 45 6. Find the other internal harness (05621138) and remove the hardware mount kits and install onto the motherboard entry bra
46 Snap Linear Knife Installing the Linear Knife – Mechanical Updates The Linear Knife is ready to install on the printer. Position the print
Snap Linear Knife 47 Installing Linear Knife onto the Lower Frame Support 4. Position the knife unit so that it rests onto the lower frame
48 Snap Linear Knife 7. Install the stacker mount shaft removed earlier through both holes of the knife mounting bracket. 8. Secure stac
Snap Linear Knife 49 Making Electrical Connections 1. Plug the D-Shell connector from the Linear Knife into mating receptacle on the printer.
Snap Linear Knife Scope 5 Scope Introduction This manual details the installation, operation, and maintenance of the AVERY DENNISON Model SNAPTM7
50 Snap Linear Knife Installing the Nip Assembly The nip assembly that was removed from the printer to make room for the new knife will be ins
Snap Linear Knife 51 4. The nip assembly will be installed using the same screws that mounted it to the printer. 5. Holding the nip assembl
52 Snap Linear Knife Installing the Stacker on the Linear Knife The stacker that was removed from the printer will be used on the accessory kni
Snap Linear Knife 53 4. Set the stacker platform angle with the right end set as high as possible to begin with. Once the stacker starts to fi
Snap Linear Knife Assembly Drawings 55 Assembly Drawings
56 Assembly Drawings Snap Linear Knife Linear Knife Assembly Drawing 18271311331391331391361291431333211111931216615151668132852451361291413313
Snap Linear Knife Assembly Drawings 57 Nip Roller Assembly Drawing 11711739511121125611643116691161031261241261034948103128103106106120441141144
58 Assembly Drawings Snap Linear Knife Drive Train Assembly Drawing
Snap Linear Knife Assembly Drawings 59 Feed Roller Assembly Drawing 12710312360103586126266012311925105105127
6 Warranty Information Snap Linear Knife Warranty Information Warranty Policy Avery Dennison Retail Branding & Information Solutions provide
60 Assembly Drawings Snap Linear Knife Sensor Assembly Drawing 91949354949313813071251031273510312711537641043713013213813813213062651155373105
Snap Linear Knife Assembly Drawings 61 Mounting Assembly Drawing 75979510738111103761131011011011011009880
62 Assembly Drawings Snap Linear Knife Cover Assembly Drawing
Snap Linear Knife Assembly Drawings 63 Cover Assembly Drawing
64 Assembly Drawings Snap Linear Knife Harnesses MCB J27MCB J23 MCB J28MCB J26MCB J29MCB J35 Part Number: 05621138
Snap Linear Knife Assembly Drawings 65 DB J4MCB J15 Part Number: 05621139 Part Number: 05621140
66 Assembly Drawings Snap Linear Knife REAR KNIFE SENSORCONTRAST SENSORFRONT KNIFE SENSORTOP REG SENSORBOTTOM REG SENSOR Part Number: 056
Snap Linear Knife Assembly Drawings 67 Linear Knife Parts List ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY 1 010107 O-RING 1 2
68 Assembly Drawings Snap Linear Knife Linear Knife Parts List ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY 53 627801 FRAME,
Snap Linear Knife Assembly Drawings 69 Linear Knife Parts List ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY 105 990327 E-RING, 5
Snap Linear Knife Warranty Information 7 Equipment purchased and exported to regions outside local Avery Dennison office coverage are not cove
70 Assembly Drawings Snap Linear Knife ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY 155 627848 GUARD, COVER 1 156 989984 4
Snap Linear Knife Assembly Drawings 71 Revision Date Description 2.1 11/18/2013 Initial release for part number 05621395 under ECN
8 Description / Specifications Snap Linear Knife Description / Specifications Linear Knife Description The SNAP Linear Knife is an add-on acces
Snap Linear Knife Installing Linear Knife – See Appendix A 9 Installing Linear Knife – See Appendix A See Appendix A for Linear Knife Installatio
Kommentare zu diesen Handbüchern