Avery Dennison Monarch 9415 Bedienerhandbuch

FRESHMARX™9415™ LabelingSystemTC9415OH Rev. AF 5/09 ©2007 Avery Dennison Corp.

1-6 Operator’s Handbook 7. Make sure the supply clip is in the correct position to touch the edge of the supply. This clip guides the labels throug

Using the Application 2-1 USING THE APPLICATION This chapter describes how to ♦ use the application ♦ calibrate the touch screen ♦ print freshne

2-2 Operator’s Handbook About the Printer There are five control buttons located on the right side of the touch screen. Button Action Stops/cancels

Using the Application 2-3 Calibrating the Touch Screen Calibrate the touch screen so the buttons respond correctly when pressed. Do this the first ti

2-4 Operator’s Handbook Printing Freshness Labels Use the application to label any product for freshness. All products are listed under their corres

Using the Application 2-5 3. Press any product button. 4. Use the numeric buttons to enter the quantity of labels to print. Press Back to backsp

2-6 Operator’s Handbook Printing Use First Labels Apply a “Use First” label to any product on the shelf that needs to be used first. A Use First labe

Care & Maintenance 3-1 CARE & MAINTENANCE This chapter tells you how to ♦ clear label jams ♦ clean the printhead ♦ clean the printer. 3

3-2 Operator’s Handbook Clearing Label Jams To clear a jam: 1. Lower the supply door. 2. Remove any previously loaded labels. 3. Slide the r

Care & Maintenance 3-3 Cleaning the Printhead Clean the printhead after every five rolls of labels or when you see voids in the print. To clean

Each product and program carries a respective written warranty, the only warranty on which the customer can rely. Avery Dennison reserves the right

3-4 Operator’s Handbook 5. If you have the dual printer, select the printer you are cleaning. 6. Press until the cleaning card is completely thro

Troubleshooting 4-1 TROUBLESHOOTING This chapter lists some common problems and their solutions. Problem Action Screen is off when the printer is tur

4-2 Operator’s Handbook Problem Action Label exits partially out of the printer or skips a label. A label may be caught in the printer. See “Clea

Troubleshooting 4-3 Problem Action Paper Out error appears. Load labels. See “Loading Labels” in Chapter 1 for more information. Printhead Over Temp

4-4 Operator’s Handbook Printing a Diagnostics Label The diagnostics label shows the printer’s software and firmware versions and Ethernet informatio

Label Formats A-1 LABEL FORMATS Format 1 Prints 1.2” wide x 1.1” long labels. Enter the following information for each field: Field Description Descr

A-2 Operator’s Handbook Format 2 Prints 2.2” wide x 1.1” long labels. Enter the following information for each field: Field Description Description 1

Label Formats A-3 Format 3 Prints 2.2” wide x 1.5” long labels. Enter the following information for each field: Field Description Description 1 Print

A-4 Operator’s Handbook Format 4 Prints 2.2” wide x 2.0” long labels. Note: A box prints around the color-coded block that corresponds to the day-o

Label Formats A-5 Format 5 Prints 2.2” wide by 3.0” long labels. Enter the following information for each field: Field Description Description Prints

i TABLE OF CONTENTS GETTING STARTED...1-1 Using This Manual...

A-6 Operator’s Handbook Format 6 Prints 2.2” wide x 4.0” long labels. Enter the following information for each field: Field Description Store Name P

Specifications B-1 SPECIFICATIONS Printer Specifications Height: 7.75” (197 mm) Width: 17.75" (451 mm) Depth: 7.0” (178 mm) Weight w/ supply:

B-2 Operator’s Handbook

Visit www.monarch.com for sales, service,supplies, information, and telephone numbersfor our International locations.TOLL FREE:1-800-543-6650 (In the

ii LABEL FORMATS...A-1 Format 1 ...

Getting Started 1-1 GETTING STARTED Use the FreshMarx™ 9415™ Labeling System for product freshness and to label inventory. This system is available

1-2 Operator’s Handbook Unpacking the Printer After you unpack the printer, you should have the following: ♦ 9415 printer ♦ power supply and cord ♦

Getting Started 1-3 Installing the Printer To install the printer on the wall: 1. Select a suitable location for the printer on a wall. 2. Tape the

1-4 Operator’s Handbook Connecting the Printer’s Power Supply To connect the power supply to the printer: 1. Turn off the printer. Press the power

Getting Started 1-5 Loading Labels Dual printer: Printer 1 is located on the left and Printer 2 is located on the right. Printer 1 is the default